What we are going to do?
####### SUMMARY #######
Current firmware control:
show version
dir flash:
show switch
Increase block size:
ip tftp blocksize 8192
If disk space is not enough cleaning up disk:
software clean
SSH key is required after upgrade, need to control:
crypto key generate rsa
show crypto key rsa mypub
Copying firmware to master stacked switch flash:
copy tftp://10.10.10.100/cat3k_caa-universalk9.16.12.07.SPA.bin flash:
dir flash:
Starting firmware upgrade:
software install file flash:cat3k_caa-universalk9.16.12.07.SPA.bin force new
enter “yes” to reload and start upgrade
Clean up old files:
request platform software package clean switch all
Current firmware control:
show version
####### PRE UPGRADE #######
S1#show switch detail
Switch/Stack Mac Address : xyzw.aaaa.1f00 – Local Mac Address
Mac persistency wait time: Indefinite
H/W Current
Switch# Role Mac Address Priority Version State
————————————————————————————-
*1 Active xyzw.aaaa.1f00 15 V04 Ready
2 Standby bbbb.cccc.c980 5 V04 Ready
3 Member dddd.eeee.2000 1 V04 Ready
Stack Port Status Neighbors
Switch# Port 1 Port 2 Port 1 Port 2
——————————————————–
1 OK OK 2 3
2 OK OK 3 1
3 OK OK 1 2
S1#dir flash-1:
Directory of flash:/
85194 -rwx 2097152 Sep 30 2022 19:34:21 +03:00 nvram_config
85187 -rwx 74369716 Jan 19 2015 22:45:49 +03:00 cat3k_caa-base.SPA.03.02.03.SE.pkg
85188 -rwx 5808828 Jan 19 2015 22:45:50 +03:00 cat3k_caa-drivers.SPA.03.02.03.SE.pkg
85189 -rwx 32496484 Jan 19 2015 22:45:49 +03:00 cat3k_caa-infra.SPA.03.02.03.SE.pkg
85190 -rwx 30418104 Jan 19 2015 22:45:49 +03:00 cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
85191 -rwx 16059104 Jan 19 2015 22:45:49 +03:00 cat3k_caa-platform.SPA.03.02.03.SE.pkg
85192 -rwx 64586444 Jan 19 2015 22:45:50 +03:00 cat3k_caa-wcm.SPA.10.0.120.0.pkg
85193 -rwx 1224 Jan 19 2015 22:46:00 +03:00 packages.conf
85186 -rwx 3076 Nov 9 2020 16:05:59 +03:00 vlan.dat
1621966848 bytes total (1393414144 bytes free)
S1#show version
Switch Ports Model SW Version SW Image Mode
—— —– —– ———- ———- —-
1 56 WS-C3850-48T 03.02.03.SE cat3k_caa-universalk9 INSTALL
2 56 WS-C3850-48T 03.02.03.SE cat3k_caa-universalk9 INSTALL
3 56 WS-C3850-48T 03.02.03.SE cat3k_caa-universalk9 INSTALL
####### FIRMWARE UPGRADE #######
Very Important: If you do not change blocksize copying will take too much time then expected
S1#conf t
S1(config)#ip tftp blocksize 8192
S1(config)#end
S1#wr mem
S1#copy tftp://10.10.10.100/cat3k_caa-universalk9.16.12.07.SPA.bin flash:
Destination filename [cat3k_caa-universalk9.16.12.07.SPA.bin]?
Accessing tftp://10.10.10.100/cat3k_caa-universalk9.16.12.07.SPA.bin…
Loading cat3k_caa-universalk9.16.12.07.SPA.bin from 10.10.10.100 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK – 480189009 bytes]
480189009 bytes copied in 464.440 secs (1033910 bytes/sec)
S1#
S1# dir flash:*.bin
85195 -rw- 480189009 Sep 30 2022 20:37:44 +03:00 cat3k_caa-universalk9.16.12.07.SPA.bin
P.S: Below old files will be deleted after firmware upgrade and reload
S1#dir flash:
Directory of flash:/
85194 -rwx 2097152 Sep 30 2022 21:34:14 +03:00 nvram_config
85187 -rwx 74369716 Jan 19 2015 22:45:49 +03:00 cat3k_caa-base.SPA.03.02.03.SE.pkg
85188 -rwx 5808828 Jan 19 2015 22:45:50 +03:00 cat3k_caa-drivers.SPA.03.02.03.SE.pkg
85189 -rwx 32496484 Jan 19 2015 22:45:49 +03:00 cat3k_caa-infra.SPA.03.02.03.SE.pkg
85190 -rwx 30418104 Jan 19 2015 22:45:49 +03:00 cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
85191 -rwx 16059104 Jan 19 2015 22:45:49 +03:00 cat3k_caa-platform.SPA.03.02.03.SE.pkg
85192 -rwx 64586444 Jan 19 2015 22:45:50 +03:00 cat3k_caa-wcm.SPA.10.0.120.0.pkg
85197 -rw- 4780 Sep 30 2022 20:43:40 +03:00 packages.conf
85186 -rwx 3076 Nov 9 2020 16:05:59 +03:00 vlan.dat
85195 -rw- 480189009 Sep 30 2022 20:37:44 +03:00 cat3k_caa-universalk9.16.12.07.SPA.bin
85196 -rwx 1224 Jan 19 2015 22:46:00 +03:00 packages.conf.00-
85193 drwx 4096 Sep 30 2022 21:05:14 +03:00 .installer
85198 -rw- 20097668 Sep 30 2022 20:43:17 +03:00 cat3k_caa-guestshell.16.12.07.SPA.pkg
85199 -rw- 32795564 Sep 30 2022 20:43:17 +03:00 cat3k_caa-rpbase.16.12.07.SPA.pkg
85200 -rw- 400857724 Sep 30 2022 20:43:35 +03:00 cat3k_caa-rpcore.16.12.07.SPA.pkg
46466 -rw- 3414660 Sep 30 2022 20:43:35 +03:00 cat3k_caa-srdriver.16.12.07.SPA.pkg
46467 -rw- 23018112 Sep 30 2022 20:43:38 +03:00 cat3k_caa-webui.16.12.07.SPA.pkg
61953 -rw- 74 Sep 30 2022 21:05:16 +03:00 bootloader_evt_handle.log
92929 drwx 4096 Sep 30 2022 21:08:04 +03:00 core
11 drwx 4096 Sep 30 2022 20:56:57 +03:00 .prst_sync
15489 drwx 4096 Sep 30 2022 20:56:53 +03:00 .rollback_timer
23233 drwx 4096 Sep 30 2022 20:56:57 +03:00 gs_script
30979 drwx 4096 Sep 30 2022 20:56:57 +03:00 tech_support
38726 drwx 4096 Sep 30 2022 21:05:30 +03:00 dc_profile_dir
61954 -rw- 132108 Sep 30 2022 21:05:52 +03:00 memleak.tcl
61956 -rw- 76 Sep 30 2022 21:05:34 +03:00 boothelper.log
61955 -rw- 66 Sep 30 2022 20:57:16 +03:00 boothelper.old
85201 drwx 4096 Sep 30 2022 21:34:09 +03:00 .dbpersist
61957 -rw- 0 Sep 30 2022 21:07:34 +03:00 rdope_out.txt
61958 -rw- 545 Sep 30 2022 21:07:46 +03:00 rdope.log
61959 -rw- 2097152 Sep 30 2022 21:34:14 +03:00 nvram_config_bkup
92930 drwx 4096 Sep 30 2022 21:07:53 +03:00 onep
61960 -rw- 3076 Sep 30 2022 21:10:34 +03:00 stby-vlan.dat
1621966848 bytes total (345612288 bytes free)
####### STARTING UPGRADE #######
During this process firmware and microcode will be upgraded one after other and each switch will be upgrade at the same time.
S1#software install file flash:cat3k_caa-universalk9.16.12.07.SPA.bin force new
Preparing install operation …
[1]: Copying software from active switch 1 to switches 2,3
[1]: Finished copying software to switches 2,3
[1 2 3]: Starting install operation
[1 2 3]: Expanding bundle flash:cat3k_caa-universalk9.16.12.07.SPA.bin
[1 2 3]: Copying package files
[1 2 3]: Package files copied
[1 2 3]: Finished expanding bundle flash:cat3k_caa-universalk9.16.12.07.SPA.bin
[1 2 3]: Verifying and copying expanded package files to flash:
[1 2 3]: Verified and copied expanded package files to flash:
[1 2 3]: Starting compatibility checks
[1 2 3]: Bypassing peer package compatibility checks due to ‘force’ command option
[1 2 3]: Finished compatibility checks
[1 2 3]: Starting application pre-installation processing
[1 2 3]: Finished application pre-installation processing
[1]: Old files list:
Removed cat3k_caa-base.SPA.03.02.03.SE.pkg
Removed cat3k_caa-drivers.SPA.03.02.03.SE.pkg
Removed cat3k_caa-infra.SPA.03.02.03.SE.pkg
Removed cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
Removed cat3k_caa-platform.SPA.03.02.03.SE.pkg
Removed cat3k_caa-wcm.SPA.10.0.120.0.pkg
[2]: Old files list:
Removed cat3k_caa-base.SPA.03.02.03.SE.pkg
Removed cat3k_caa-drivers.SPA.03.02.03.SE.pkg
Removed cat3k_caa-infra.SPA.03.02.03.SE.pkg
Removed cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
Removed cat3k_caa-platform.SPA.03.02.03.SE.pkg
Removed cat3k_caa-wcm.SPA.10.0.120.0.pkg
[3]: Old files list:
Removed cat3k_caa-base.SPA.03.02.03.SE.pkg
Removed cat3k_caa-drivers.SPA.03.02.03.SE.pkg
Removed cat3k_caa-infra.SPA.03.02.03.SE.pkg
Removed cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
Removed cat3k_caa-platform.SPA.03.02.03.SE.pkg
Removed cat3k_caa-wcm.SPA.10.0.120.0.pkg
[1]: New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
[2]: New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
[3]: New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
[1 2 3]: Creating pending provisioning file
[1 2 3]: Finished installing software. New software will load on reboot.
[1 2 3]: Committing provisioning file
[1 2 3]: Do you want to proceed with reload? [yes/no]: yes
[2 3]: Reloading
[1]: Pausing before reload[1]: Reloading
S1#
####### CONSOLE LOGS #######
Sep 30 20:49:33: %STACKMGR-1-RELOAD_REQUEST: 1 stack-mgr: Received reload request for switch 2, reason User requested reload
Sep 30 20:49:33: %STACKMGR-1-STACK_LINK_CHANGE: 1 stack-mgr: Stack port 1 on switch 1 is down
Sep 30 20:49:33: %STACKMGR-1-STACK_LINK_CHANGE: MEMBER: 3 stack-mgr: Stack port 2 on switch 3 is down
Sep 30 20:49:33: %STACKMGR-1-SWITCH_REMOVED: 1 stack-mgr: Switch 2 has been removed from the stack.
Sep 30 20:49:33: %SPANTREE-5-TOPOTRAP: Topology Change Trap for vlan 1
Sep
S1#30 20:49:34: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT)
Sep 30 20:49:34: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby removal (raw-event=PEER_NOT_PRESENT(3))
Sep 30 20:49:34: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN)
Sep 30 20:49:34: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected standby down or crashed (raw-event=PEER_DOWN(2))
Sep 30 20:49:34: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_REDUNDANCY_STATE_CHANGE)
Sep
S1#30 20:49:34: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby removal (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5))
Sep 30 20:49:33: %STACKMGR-1-SWITCH_REMOVED: MEMBER: 3 stack-mgr: Switch 2 has been removed from the stack.
Sep 30 20:49:34: %STACKMGR-1-RELOAD: MEMBER: 3 stack-mgr: Reloading due to reason User requested reload
<Fri Sep 30 17:49:49 2022> Message from sysmgr: Reset Reason:Reset/Reload requested by [stack-manager]. [User requested reload]
Unmounting ng3k filesystems…
Unmounted /dev/sda3…
Warning! – some ng3k filesystems may not have unmounted cleanly…
Please stand by while rebooting the system…
Restarting system.
Booting…Initializing and Testing RAM ++++@@@@####…################################++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@++@@done.
Memory Test Pass!
Base ethernet MAC Address: 68:9c:e2:33:1f:00
Interface GE 0 link down***ERROR: PHY link is down
Initializing Flash…
flashfs[7]: 0 files, 1 directories
flashfs[7]: 0 orphaned files, 0 orphaned directories
flashfs[7]: Total bytes: 6784000
flashfs[7]: Bytes used: 1024
flashfs[7]: Bytes available: 6782976
flashfs[7]: flashfs fsck took 1 seconds….done Initializing Flash.
Getting rest of image
Reading full image into memory….done
Reading full base package into memory…: done = 32795564
Nova Bundle Image
————————————–
Kernel Address : 0x6042e3c4
Kernel Size : 0x4381df/4424159
Initramfs Address : 0x608665a3
Initramfs Size : 0x1ab5e09/28007945
Compression Format: mzip
Bootable image at @ ram:0x6042e3c4
Bootable image segment 0 address range [0x81100000, 0x81da5280] is in range [0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@boot_system: 380
Loading Linux kernel with entry point 0x81895bf0 …
Bootloader: Done loading app on core_mask: 0xf
### Launching Linux Kernel (flags = 0x5)
Linux version 4.9.187 (sumikum7@sjc-ads-5670) (gcc version 5.3.0 (GCC) ) #1 SMP Fri Nov 19 03:09:46 PST 2021
CVMSEG size: 2 cache lines (256 bytes)
Cavium Inc. SDK-5.1.0
bootconsole [early0] enabled
CPU0 revision is: 000d900a (Cavium Octeon II)
Checking for the multiply/shift bug… no.
Checking for the daddiu bug… no.
%IOSXEBOOT-3748f25d3076de52df7db2641f93e50c-new_cksum: (rp/0): 4
%IOSXEBOOT-3748f25d3076de52df7db2641f93e50c-saved_cksum: (rp/0): 4
%IOSXEBOOT-Fri-###: (rp/0): Sep 30 17:57:01 Universal 2022 PLEASE DO NOT POWER CYCLE ### BOOT LOADER UPGRADING 4
%IOSXEBOOT-loader-boot: (rp/0): upgrade successful 4
Final tar file: mcu_ucode_bundle_6_2_0.tar
MM [1] MCU version 136 sw ver 83
MM [2] MCU version 136 sw ver 83
MM [3] MCU version 17 bl ver 16
Front-end Microcode IMG MGR: found 4 microcode images for 1 device.
Image for front-end 0: /tmp/microcode_update/front_end/fe_type_6_0 update needed: no
Image for front-end 0: /tmp/microcode_update/front_end/fe_type_6_1 update needed: yes
Image for front-end 0: /tmp/microcode_update/front_end/fe_type_6_2 update needed: yes
Image for front-end 0: /tmp/microcode_update/front_end/fe_type_6_3 update needed: yes
Front-end Microcode IMG MGR: Preparing to program device microcode…
Front-end Microcode IMG MGR: Preparing to program device[0], index=0 …594412 bytes…. Skipped[0].
Front-end Microcode IMG MGR: Preparing to program device[0], index=1 …452272 bytes.
Front-end Microcode IMG MGR: Programming device 0…rwRrrrrrrw..0%…………………………………………………………………………10%…………………………………………………………………………20%………………………………………………………………………..30%…………………………………………………………………………40%………………………………………………………………………..50%…………………………………………………………………………..60%………………………………………………………………………..70%…………………………………………………………………………80%…………………………………………………………………………90%………………………………………………………………………..100%
Front-end Microcode IMG MGR: Preparing to program device[0], index=2 …25210 bytes.
Front-end Microcode IMG MGR: Programming device 0…rrrrrrw..0%….10%….20%……30%…40%……50%….60%……70%…80%……90%….100%
Front-end Microcode IMG MGR: Preparing to program device[0], index=3 …90974 bytes.
Front-end Microcode IMG MGR: Programming device 0…rrrrrrw..0%…………….10%……………..20%……………..30%……………..40%……………..50%……………..60%……………..70%……………..80%……………90%………………100%w
Front-end Microcode IMG MGR: Microcode programming complete in 318 seconds
% Front-end Microcode IMG MGR: HW image is upgraded. MCU reset causes the switch to reload
Booting…
Interface GE 0 link down***ERROR: PHY link is down
Getting rest of image
Reading full image into memory…Check base package header …: done = 16384
Getting rest of image
Reading full image into memory….done
Reading full base package into memory…: done = 32795564
Bundle Image
————————————–
Kernel Address : 0x537783c4
Kernel Size : 0x4381df/4424159
Initramfs Address : 0x53bb05a3
Initramfs Size : 0x1ab5e09/28007945
Compression Format: mzip
Bootable image at @ ram:0x537783c4
Bootable image segment 0 address range [0x81100000, 0x81da5280] is in range [0x80180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@boot_system: 623
Loading Linux kernel with entry point 0x81895bf0 …
Bootloader: Done loading app on core_mask: 0xf
### Launching Linux Kernel (flags = 0x5)
Linux version 4.9.187 (sumikum7@sjc-ads-5670) (gcc version 5.3.0 (GCC) ) #1 SMP Fri Nov 19 03:09:46 PST 2021
CVMSEG size: 2 cache lines (256 bytes)
Cavium Inc. SDK-5.1.0
bootconsole [early0] enabled
CPU0 revision is: 000d900a (Cavium Octeon II)
Checking for the multiply/shift bug… no.
Checking for the daddiu bug… no.
%IOSXEBOOT-3748f25d3076de52df7db2641f93e50c-new_cksum: (rp/0): 4
%IOSXEBOOT-3748f25d3076de52df7db2641f93e50c-saved_cksum: (rp/0): 4
Final tar file: mcu_ucode_bundle_6_2_0.tar
Waiting for 120 seconds for other switches to boot
#####
Switch number is 1
All switches in the stack have been discovered. Accelerating discovery
…………………
…………………
…………………
*Sep 30 18:07:31.798: %PLATFORM-3-BACKUP_NVRAM_OPEN_FAIL: Failed to open backup nvram – No such file or directory.
*Sep 30 18:07:31.798: %IOSXE_RP_NV-3-BACKUP_NV_ACCESS_FAIL: Initial read of backup NVRAM contents failed
*Sep 30 18:07:33.987: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is initialized
*Sep 30 18:07:33.988: %SMART_LIC-6-AGENT_ENABLED: Smart Agent for Licensing is enabled
*Sep 30 18:07:33.993: %SMART_LIC-6-EXPORT_CONTROLLED: Usage of export controlled features is not allowed
*Sep 30 18:07:46.397: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Sep 30 18:07:48.038: %LINK-3-UPDOWN: Interface Lsmpi18/3, changed state to up
*Sep 30 18:07:48.040: %LINK-3-UPDOWN: Interface EOBC18/1, changed state to up
*Sep 30 18:07:48.041: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Sep 30 18:07:48.042: %LINK-3-UPDOWN: Interface LIIN18/2, changed state to up
*Sep 30 18:07:48.389: %HMANRP-6-HMAN_IOS_CHANNEL_INFO: HMAN-IOS channel event for switch 3: EMP_RELAY: Channel UP!
*Sep 30 18:07:48.394: %HMANRP-6-HMAN_IOS_CHANNEL_INFO: HMAN-IOS channel event for switch 2: EMP_RELAY: Channel UP!
*Sep 30 18:07:48.405: %HMANRP-6-HMAN_IOS_CHANNEL_INFO: HMAN-IOS channel event for switch 1: EMP_RELAY: Channel UP!
*Sep 30 18:07:48.414: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Sep 30 18:07:48.421: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Sep 30 18:06:37.903: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 1 on Switch 1 is down
*Sep 30 18:06:37.903: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 2 on Switch 1 is down
*Sep 30 18:06:42.247: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 1 on Switch 1 is up
*Sep 30 18:06:42.989: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 2 on Switch 1 is up
*Sep 30 18:06:43.219: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 1 has been added to the stack.
*Sep 30 18:06:47.276: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 3 has been added to the stack.
*Sep 30 18:06:49.380: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 1 has been added to the stack.
*Sep 30 18:06:49.380: %STACKMGR-6-ACTIVE_ELECTED: Switch 1 R0/0: stack_mgr: Switch 1 has been elected ACTIVE.
*Sep 30 18:06:39.632: %STACKMGR-6-STACK_LINK_CHANGE: Switch 3 R0/0: stack_mgr: Stack port 1 on Switch 3 is down
*Sep 30 18:06:39.632: %STACKMGR-6-STACK_LINK_CHANGE: Switch 3 R0/0: stack_mgr: Stack port 2 on Switch 3 is down
*Sep 30 18:06:43.755: %STACKMGR-6-STACK_LINK_CHANGE: Switch 3 R0/0: stack_mgr: Stack port 1 on Switch 3 is up
*Sep 30 18:06:43.976: %STACKMGR-6-STACK_LINK_CHANGE: Switch 3 R0/0: stack_mgr: Stack port 2 on Switch 3 is up
*Sep 30 18:06:43.981: %STACKMGR-4-SWITCH_ADDED: Switch 3 R0/0: stack_mgr: Switch 3 has been added to the stack.
*Sep 30 18:06:48.037: %STACKMGR-4-SWITCH_ADDED: Switch 3 R0/0: stack_mgr: Switch 3 has been added to the stack.
*Sep 30 18:06:50.036: %STACKMGR-4-SWITCH_ADDED: Switch 3 R0/0: stack_mgr: Switch 3 has been added to the stack.
*Sep 30 18:06:50.156: %STACKMGR-6-ACTIVE_ELECTED: Switch 3 R0/0: stack_mgr: Switch 1 has been elected ACTIVE.
*Sep 30 18:06:37.913: %STACKMGR-6-STACK_LINK_CHANGE: Switch 2 R0/0: stack_mgr: Stack port 1 on Switch 2 is down
*Sep 30 18:06:37.913: %STACKMGR-6-STACK_LINK_CHANGE: Switch 2 R0/0: stack_mgr: Stack port 2 on Switch 2 is down
*Sep 30 18:06:42.247: %STACKMGR-6-STACK_LINK_CHANGE: Switch 2 R0/0: stack_mgr: Stack port 2 on Switch 2 is up
*Sep 30 18:06:43.213: %STACKMGR-6-STACK_LINK_CHANGE: Switch 2 R0/0: stack_mgr: Stack port 1 on Switch 2 is up
*Sep 30 18:06:43.219: %STACKMGR-4-SWITCH_ADDED: Switch 2 R0/0: stack_mgr: Switch 2 has been added to the stack.
*Sep 30 18:06:47.277: %STACKMGR-4-SWITCH_ADDED: Switch 2 R0/0: stack_mgr: Switch 3 has been added to the stack.
*Sep 30 18:06:49.393: %STACKMGR-4-SWITCH_ADDED: Switch 2 R0/0: stack_mgr: Switch 2 has been added to the stack.
*Sep 30 18:06:49.393: %STACKMGR-6-ACTIVE_ELECTED: Switch 2 R0/0: stack_mgr: Switch 1 has been elected ACTIVE.
*Sep 30 18:07:48.432: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Sep 30 18:07:48.434: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Sep 30 18:07:49.070: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 2 stack power cable 2 inserted
*Sep 30 18:07:49.070: %PLATFORM_STACKPOWER-6-LINK_EVENT: Switch 2 stack power protocol is up on cable 2
*Sep 30 18:07:49.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi18/3, changed state to up
*Sep 30 18:07:49.082: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC18/1, changed state to up
*Sep 30 18:07:49.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
*Sep 30 18:07:49.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN18/2, changed state to up
*Sep 30 18:07:49.464: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 1 stack power cable 2 inserted
*Sep 30 18:07:49.465: %PLATFORM_STACKPOWER-6-LINK_EVENT: Switch 1 stack power protocol is up on cable 2
*Sep 30 18:07:49.615: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 3 stack power cable 2 inserted
*Sep 30 18:07:49.615: %PLATFORM_STACKPOWER-6-LINK_EVENT: Switch 3 stack power protocol is up on cable 2
*Sep 30 18:07:51.882: %SYS-5-CONFIG_P: Configured programmatically by process MGMT VRF Process from console as vty0
*Sep 30 18:07:51.894: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-vrf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Sep 30 18:07:51.897: %SYS-5-CONFIG_P: Configured programmatically by process MGMT VRF Process from console as vty0
*Sep 30 18:07:53.586: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Base was enabled by Default
*Sep 30 18:07:54.369: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Sep 30 18:07:56.461: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-1945037290 has been generated or imported by crypto config
*Sep 30 18:07:56.475: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-1473100509 has been generated or imported by crypto config
*Sep 30 18:07:56.495: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named S1.milsoft.com.tr has been generated or imported by crypto config
*Sep 30 18:07:56: %SYS-5-LOG_CONFIG_CHANGE: Console logging: level informational, xml disabled, filtering disabled
*Sep 30 18:07:56: %SYS-5-LOG_CONFIG_CHANGE: Monitor logging: level errors, xml disabled, filtering disabled
*Sep 30 21:07:56: %SYS-6-CLOCKUPDATE: System clock has been updated from 18:07:56 UTC Fri Sep 30 2022 to 21:07:56 TRT Fri Sep 30 2022, configured from console by vty0.
*Sep 30 21:07:56: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 30 21:07:56: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 30 21:07:56: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 30 21:07:56: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 30 21:07:56: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TP-self-signed-1473100509 created succesfully
*Sep 30 21:07:59: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Sep 30 21:07:59: %LINK-5-CHANGED: Interface GigabitEthernet1/0/47, changed state to administratively down
*Sep 30 21:07:59: %LINK-5-CHANGED: Interface GigabitEthernet2/0/7, changed state to administratively down
*Sep 30 21:08:01: %SYS-5-CONFIG_I: Configured from memory by console
*Sep 30 21:08:01: %SYS-5-CONFIG_P: Configured programmatically by process CPP MQC QoS Policy manager from console as vty1
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/3, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/4, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/3, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/4, changed state to down
*Sep 30 21:08:04: %SYS-5-RESTART: System restarted —
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 16.12.7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Wed 02-Feb-22 07:28 by mcpre
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/3, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet2/1/4, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet2/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet2/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet2/1/3, changed state to down
*Sep 30 21:08:04: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet2/1/4, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet3/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet3/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet3/1/3, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface GigabitEthernet3/1/4, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet3/1/1, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet3/1/2, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet3/1/3, changed state to down
*Sep 30 21:08:04: %LINK-3-UPDOWN: Interface TenGigabitEthernet3/1/4, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/1, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/2, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/3, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/4, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/1, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/2, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/3, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/4, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/1/1, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/1/2, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/1/3, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/1/4, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/1, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/2, changed state to down
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/3, changed state to down
*Sep 30 21:08:05: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 10.0.0.251 port 514 started – CLI initiated
*Sep 30 21:08:05: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 10.0.0.211 port 514 started – CLI initiated
*Sep 30 21:08:05: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 10.0.0.114 port 514 started – CLI initiated
*Sep 30 21:08:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/1/4, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3/1/1, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3/1/2, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3/1/3, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3/1/4, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet3/1/1, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet3/1/2, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet3/1/3, changed state to down
*Sep 30 21:08:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet3/1/4, changed state to down
*Sep 30 21:08:06: %LINK-3-UPDOWN: Interface Vlan1, changed state to up
*Sep 30 21:08:06: %PKI-2-NON_AUTHORITATIVE_CLOCK: PKI functions can not be initialized until an authoritative time source, like NTP, can be obtained.
*Sep 30 21:08:07: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI_LEGACY created succesfully
*Sep 30 21:08:07: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_SUDI_LEGACY has been generated or imported by pki-sudi
*Sep 30 21:08:07: %SNMP-5-COLDSTART: SNMP agent on host S1 is undergoing a cold start
*Sep 30 21:08:09: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/25, changed state to up
*Sep 30 21:08:09: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI0 created succesfully
*Sep 30 21:08:09: %IOSXE_INFRA-6-PROCPATH_CLIENT_HOG: IOS shim client ‘pkissl reader mqipc’ has taken 1948 msec (runtime: 260 msec) to process a ‘unknown’ message
*Sep 30 21:08:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/25, changed state to up
*Sep 30 21:08:11: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Startup Config Present)
*Sep 30 21:08:11: %SYS-5-CONFIG_P: Configured programmatically by process EPM CREATE DEFAULT CWA URL ACL from console as console
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/5, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet3/0/5, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet3/0/7, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/6, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/33, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/24, changed state to up
*Sep 30 21:08:11: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/9, changed state to up
*Sep 30 21:08:12: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/35, changed state to up
*Sep 30 21:08:12: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/14, changed state to up
*Sep 30 21:08:12: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/42, changed state to up
*Sep 30 21:08:12: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-1945037290.server has been generated or imported by crypto-engine
*Sep 30 21:10:03: %IOSXE_REDUNDANCY-6-PEER: Active detected switch 2 as standby.
*Sep 30 21:10:03: %STACKMGR-6-STANDBY_ELECTED: Switch 1 R0/0: stack_mgr: Switch 2 has been elected STANDBY.
–More–
*Sep 30 21:10:17: %SYS-6-CLOCKUPDATE: System clock has been updated from 21:10:15 TRT Fri Sep 30 2022 to 21:10:17 TRT Fri Sep 30 2022, configured from NTP by 10.0.0.100.
–More–
*Sep 30 21:10:17: %SMART_LIC-5-SYSTEM_CLOCK_CHANGED: Smart Agent for Licensing System clock has been changed
–More–
*Sep 30 21:10:24: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_FOUND(4))
*Sep 30 21:10:24: %REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion (raw-event=PEER_REDUNDANCY_STATE_CHANGE(5))
############ POST UPGRADE #########
Cleaning up old files to freeing space
S1# request platform software package clean switch all
This operation may take several minutes…
Running command on switch 1
Cleaning up unnecessary package files
No path specified, will use booted path flash:packages.conf
Cleaning flash:
Scanning boot directory for packages … done.
Preparing packages list to delete …
cat3k_caa-guestshell.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpbase.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpcore.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-srdriver.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-webui.16.12.07.SPA.pkg
File is in use, will not delete.
packages.conf
File is in use, will not delete.
done.
Running command on switch 2
Cleaning up unnecessary package files
No path specified, will use booted path flash:packages.conf
Cleaning flash:
Scanning boot directory for packages … done.
Preparing packages list to delete …
cat3k_caa-guestshell.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpbase.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpcore.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-srdriver.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-webui.16.12.07.SPA.pkg
File is in use, will not delete.
packages.conf
File is in use, will not delete.
done.
Running command on switch 3
Cleaning up unnecessary package files
No path specified, will use booted path flash:packages.conf
Cleaning flash:
Scanning boot directory for packages … done.
Preparing packages list to delete …
cat3k_caa-guestshell.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpbase.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-rpcore.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-srdriver.16.12.07.SPA.pkg
File is in use, will not delete.
cat3k_caa-webui.16.12.07.SPA.pkg
File is in use, will not delete.
packages.conf
File is in use, will not delete.
done.
The following files will be deleted:
[switch 1]:
/flash/cat3k_caa-base.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-drivers.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-infra.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
/flash/cat3k_caa-platform.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-universalk9.16.12.07.SPA.bin
/flash/cat3k_caa-wcm.SPA.10.0.120.0.pkg
/flash/packages.conf.00-
[switch 2]:
/flash/cat3k_caa-base.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-drivers.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-infra.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
/flash/cat3k_caa-platform.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-universalk9.16.12.07.SPA.bin
/flash/cat3k_caa-wcm.SPA.10.0.120.0.pkg
/flash/packages.conf.00-
[switch 3]:
/flash/cat3k_caa-base.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-drivers.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-infra.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg
/flash/cat3k_caa-platform.SPA.03.02.03.SE.pkg
/flash/cat3k_caa-universalk9.16.12.07.SPA.bin
/flash/cat3k_caa-wcm.SPA.10.0.120.0.pkg
/flash/packages.conf.00-
Do you want to proceed? [y/n]y
[switch 1]:
Deleting file flash:cat3k_caa-base.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-drivers.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-infra.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg … done.
Deleting file flash:cat3k_caa-platform.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-universalk9.16.12.07.SPA.bin … done.
Deleting file flash:cat3k_caa-wcm.SPA.10.0.120.0.pkg … done.
Deleting file flash:packages.conf.00- … done.
SUCCESS: Files deleted.
[switch 2]:
Deleting file flash:cat3k_caa-base.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-drivers.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-infra.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg … done.
Deleting file flash:cat3k_caa-platform.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-universalk9.16.12.07.SPA.bin … done.
Deleting file flash:cat3k_caa-wcm.SPA.10.0.120.0.pkg … done.
Deleting file flash:packages.conf.00- … done.
SUCCESS: Files deleted.
[switch 3]:
Deleting file flash:cat3k_caa-base.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-drivers.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-infra.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-iosd-universalk9.SPA.150-1.EX3.pkg … done.
Deleting file flash:cat3k_caa-platform.SPA.03.02.03.SE.pkg … done.
Deleting file flash:cat3k_caa-universalk9.16.12.07.SPA.bin … done.
Deleting file flash:cat3k_caa-wcm.SPA.10.0.120.0.pkg … done.
Deleting file flash:packages.conf.00- … done.
SUCCESS: Files deleted.
S1#
S1#dir flash:
Directory of flash:/
85194 -rwx 2097152 Sep 30 2022 21:34:14 +03:00 nvram_config
85197 -rw- 4780 Sep 30 2022 20:43:40 +03:00 packages.conf
85186 -rwx 3076 Nov 9 2020 16:05:59 +03:00 vlan.dat
85193 drwx 4096 Sep 30 2022 21:05:14 +03:00 .installer
85198 -rw- 20097668 Sep 30 2022 20:43:17 +03:00 cat3k_caa-guestshell.16.12.07.SPA.pkg
85199 -rw- 32795564 Sep 30 2022 20:43:17 +03:00 cat3k_caa-rpbase.16.12.07.SPA.pkg
85200 -rw- 400857724 Sep 30 2022 20:43:35 +03:00 cat3k_caa-rpcore.16.12.07.SPA.pkg
46466 -rw- 3414660 Sep 30 2022 20:43:35 +03:00 cat3k_caa-srdriver.16.12.07.SPA.pkg
46467 -rw- 23018112 Sep 30 2022 20:43:38 +03:00 cat3k_caa-webui.16.12.07.SPA.pkg
61953 -rw- 74 Sep 30 2022 21:05:16 +03:00 bootloader_evt_handle.log
92929 drwx 4096 Sep 30 2022 21:08:04 +03:00 core
11 drwx 4096 Sep 30 2022 20:56:57 +03:00 .prst_sync
15489 drwx 4096 Sep 30 2022 20:56:53 +03:00 .rollback_timer
23233 drwx 4096 Sep 30 2022 20:56:57 +03:00 gs_script
30979 drwx 4096 Sep 30 2022 20:56:57 +03:00 tech_support
38726 drwx 4096 Sep 30 2022 21:05:30 +03:00 dc_profile_dir
61954 -rw- 132108 Sep 30 2022 21:05:52 +03:00 memleak.tcl
61956 -rw- 76 Sep 30 2022 21:05:34 +03:00 boothelper.log
61955 -rw- 66 Sep 30 2022 20:57:16 +03:00 boothelper.old
85201 drwx 4096 Sep 30 2022 21:34:09 +03:00 .dbpersist
61957 -rw- 0 Sep 30 2022 21:07:34 +03:00 rdope_out.txt
61958 -rw- 545 Sep 30 2022 21:07:46 +03:00 rdope.log
61959 -rw- 2097152 Sep 30 2022 21:34:14 +03:00 nvram_config_bkup
92930 drwx 4096 Sep 30 2022 21:07:53 +03:00 onep
61960 -rw- 3076 Sep 30 2022 21:10:34 +03:00 stby-vlan.dat
S1#show version
………..
………..
………..
Switch Ports Model SW Version SW Image Mode
—— —– —– ———- ———- —-
* 1 56 WS-C3850-48T 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
2 56 WS-C3850-48T 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
3 56 WS-C3850-48T 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
Reference Link:
Notes to Myself 